Paypal accepted if you cover the fee they charge.

Much of this stuff is now on ebay under seller stang8s@aol.com

Click links for Pictures!

VP C16 Racing Fuel. 33 Gallon drum with aprox 25 gal. left. $125 reduced to $100

342 Rotating assy. Scat forged steel stroker crank 3.4 stroke, Oliver 5.4 billet rods, Venolia custom pistons (12 runs) 9:1 dished-stock 4.0 bore, tool steel pins (12 runs), groove spacers, file fit rings (12 runs). Internally 0 balanced by keith craft. $3000 reduced to $2500 or best offer Reduced to $2000

Dart sr heads fully ported flowing over 300. Manley severe duty valves 2.055/1.625, kmotion tit retainers, K900 springs $1500 complete Machined for bronze guides, teflon seals, high lift and larger springs. $1500 or best offer Reduced to $1000 (SOLD)

Lunati 1 pc chromemoly pushrods- stock length $75 Reduced to $50 (SOLD)

86 body with wolfe sway bar, 87-93 harwood hood and custom moly cage/through floor connectors $2000  (SOLD)

Strange 4 lug 8.8 rear drag brakes with braided lines $500  (SOLD)

Lakewood driveshaft safety loop (SOLD)

8.8 Rearend with moser 31 spline axles, motorsports 3:55 gears, Strange spool, Moser c-clip eliminators, TA cover/girdle, MW 9" style yoke, moroso studs 4lug. $800 (SOLD)

Weldon pump (12 runs) 2035. $650 lowered to $600 (SOLD)

MSD RPM pills 4000, 3000, 7000(SOLD)series $15 per series of 5. (SOLD)

Comp Eng Wheelie bars $170 (SOLD)

Autometer fuel pressure guage $25 (SOLD)

15x10 Weld draglites, 4 lug with MT 28x10.5x15 ET drag slicks and screws. 12 runs. $450 (SOLD)

83# injectors (12 runs since flow, new orings and screens) $400 (SOLD)

Taylor battery box and cables $90 (SOLD)

Aerospace 4 lug drag front brakes with braided lines and spindles $400 PIC1 PIC2 PIC3 PIC4 (SOLD)

Hurst Linelock with switch $80 (SOLD)

Twin turbo kit $4000 reduced to $3700 (SOLD)

Custom turbo people solid roller cam (12 runs) $200 (SOLD)

100 Amp 1 wire chrome alternator $80 (SOLD)

Aerospace Rear disc brakes Brand new in package, never installed. Race kit for 4 lug axles. 4 piston calipers. $375 (SOLD)

15x3.5" Weld draglites, 4 lug with MT ET fronts, like new. 12 runs  (SOLD)

Innovative turbo Multi stage electronic boost controller kit $400 PIC1     PIC2 (SOLD)

UPR caster/camber plates $120 (SOLD)

Electronic volt meter (new in box) $70 (SOLD)

UPR double adjustable upper control arms $125 (SOLD)

MSD 7AL2 with power coil $300 (SOLD)

Digital EGT with probe $150 (SOLD)

MT ET slicks 29.5x10.5-15W (SOLD)

5 gallon fuel cell $90 (SOLD)

UPR Tubular A-arms with wolfe travel limiters $220 (SOLD)

UPR front coilover kit $140 (SOLD)

Lakewood 90/10 struts $120 (SOLD)

Aerospace master cylinder, manual brake plate, rod. $120 (SOLD)

D&D tubular Kmember $250 (SOLD)

Koni double adjustable rear coilovers with 150# springs $500 (SOLD)

Wolfe offset solid adjustable rear lower control arms $150  (SOLD)

Wolfe spherical bushings $80 (SOLD)

Dynamic/TCT Powerglide 10" turbo spline race conv $400 (SOLD)

Dynamic Powerglide  ultrabell, brake, tci shield. Built with roller bearings, turbo vasco shaft, 7 clutch drums, 1.76 ford gearset, kevlar bands, teflon seals, koleen steels, protree brake $1300  (SOLD)

Complete stainless braided fuel lines with AN fittings for fox chassis. -12 sump to filter, -10 pump to Yblock, 2x -8 Yblock to rails, 2x -6 rail returns to regulator, -6 regulator to fuel cell.  (SOLD)

A4 block std bore $1000 (SOLD)

Canton 7 qt pan with pickup and dipstick and two drain fittings $180 (SOLD)

Accumulator system with remote valve and brackets. $250 (SOLD)

Canton Remote Oil filter canister and billet engine bypass kit. ($100) (SOLD)

2 Billet fuel filters 1 UPR -12 $60(SOLD) and 1 system1 -10 $50 (SOLD)

Accel DFI programmed by Spetter with knock module, Dan white harness adapter, sensors, 3 bar mapp, calmap, cable and laptop Also including factory injector, main engine and o2 harnesses with all needed GM connectors, O2 sensor, TPS sensor, GM idle air bypass, air and water sensors $1000 complete (SOLD)

Crower stainless rockers (12 runs) 1.60 $300 (SOLD)

Rocker Stud Girdles-Omega $75 (SOLD)

Lunati solid roller lifters $200 (SOLD)

7 Pass tranny cooler with -6 braided stainless lines and fittings $60 (SOLD)

Downs modified/ported/flowed upper intake $300(SOLD) and spacer for GT40 $30 (SOLD)

GT40 Lower (SOLD)

Accufab 75mm (SOLD)

Cartech 1/2 Rails with fittings $100 (SOLD) and regulator modified for high flow with liquid filled gauge and all fittings $100 (SOLD)

MS tall polished valve covers $75 (SOLD)

MS Timing Set (SOLD)

ARP head studs (nuts included but not pictured) $50 (SOLD)

Aluminum Breather Catch can Setup $150 (SOLD)

Solid aluminum motor mounts $50 (SOLD)

Autometer Oil $25/water $30 guages (SOLD) ,Autometer Tranny temp gauge with block $50 (SOLD)  Autometer tach $120,(SOLD)  , delay box $150 (SOLD)

Sportcomp Boost guage $30 (SOLD), Autometer boost memory kit $20 (SOLD)

Painless wiring 6 switch panel $90 (SOLD)

Aluminum front timing cover $50 (SOLD)

Fox Tranny crossmember with poly bushings $50 (SOLD)

Weld Draglites 5 lug 15x10 6.5" BS $200 (SOLD)

9" rear center section. Aluminum pinion support, Steel 35 spline spool, Moser Nodular housing, Richmond gears, All grade 8 bolts and bearings. Never run, only used for rolling car around. Housing has rust from sitting. Cost over $1000 new Sell for $700. (SOLD)